Before
After
Every hour your facility operates depends on the fixtures above your employee's heads. So why would you trust that to a cheap imported product with unknown components, no direct support, and a warranty backed by a company you can't talk to directly?
Get Your Free Assessment →Your production operation doesn't stop because it's convenient. Neither does your loading dock, your quality line, or your third shift. When a fixture fails in a 35-foot bay over an active operation, you're not just replacing a light - you're shutting down a zone, renting a lift, pulling a crew, and losing output. That's not a maintenance issue. That's a production problem caused by a purchasing decision.
eneroi installs American-made LED fixtures sourced direct from the manufacturer - with known, high-end components, domestic factory support, and an engineering spec built to thrive in the environment they're going into. Not a container of commodity product with a sticker on it.
We model every facility in AGi32 and design to exact foot-candle specs for your application - production floors, inspection zones, aisleways, loading docks. Not a one-for-one swap. An engineered layout tuned to how your facility actually operates.
The cheapest fixture on the spec sheet is never the cheapest fixture over ten years. When you factor in energy consumption, relamping labor, lift rentals, and early failure - the imported product costs more. Every time. We show you the real math.
Different areas of your facility need different light levels at different times. eneroi integrates wireless controls that let you tune output by zone - full brightness on the production floor, dimmed in storage, off in empty bays. Your energy bill reflects exactly what you're using.
When you need a replacement or have a technical question, you're not calling an 800 number that routes to an agency who calls a distributor that calls the factory. You have direct access to the people who built the fixture. American-made. American-supported. End of story.
Industrial environments destroy lighting that wasn't engineered for them. Heat, dust, vibration, chemical exposure, washdown cycles, and extreme mounting heights all take their toll. Every fixture eneroi specs is selected for the specific conditions it's going into - not pulled from a catalog and hoped for the best.
Thermal management designed for sustained ambient temps above 122°F. LED drivers and chips rated to perform in environments that kill standard fixtures.
Sealed housings and gasketed lenses that keep contamination out. Our fixtures are designed so dust and particles pass through the housing rather than getting trapped on top - unlike cheap LED fixtures where debris accumulates and cooks the LED from within, degrading output and shortening life.
Solid-state LED has no filament to break. Fixtures spec'd with 3G-rated vibration resistance, reinforced mounting, and vibration-resistant drivers for stamping, pressing, and heavy machinery areas.
30–50ft bays, overhead cranes, mezzanine structures. When it costs $500+ just to access a fixture, you need it to last. Ours do.
Food processing, beverage, pharmaceutical. IP-rated fixtures with conformal-coated LEDs that handle direct spray, sanitation chemicals, and high-humidity environments without corrosion.
Instant-on at full brightness in sub-zero environments. No warm-up time, no reduced output, no premature failure from thermal cycling.
Real client. Real data. Metered before and after over a full calendar year. We don't hand you a projection and disappear - we document what actually changed and put it in writing. The utility bills don't lie.
Most industrial facilities see energy reductions of 40-70% on lighting costs. The exact savings depend on your current fixtures, operating hours, and utility rates. Every eneroi project includes a detailed savings model specific to your facility before you commit.
No. We install around your schedule and have completed projects inside 24/7 operating environments with zero production disruption.
We guarantee the energy savings we project for your facility. If the savings fall short, we cover the difference. The guarantee is insured through Lloyd's of London.
Imported fixtures fail early, use lower-grade LED drivers and chips, and have no domestic support. Our American-made fixtures are built to last in harsh industrial environments, come with factory-direct technical support, and carry longer warranties.
Most industrial LED retrofits pay for themselves in under 24 months when you factor in energy savings, maintenance elimination, utility rebates (where available), and 100% bonus depreciation under current federal tax law.
Get a free on-site assessment from an eneroi lighting expert. We'll audit your facility, model the light levels, show you the real total cost of ownership, and identify every available utility rebate. Proposal back to you within a week. No obligation.
Get Your Free Industrial Lighting Assessment →